www.beadsbaublesandjewels.com
1613-2 Print | Close [X]
Jackie Truty makes a one of a kind lentil bead using art clay silver and then shows how to add patina for a vintage look.

Watch the video for this project at YouTube: http://youtu.be/_8pqJ9Ell1c



For More Information Visit:

www.JTV.com/JewelSchool

Carving Your Own Texture Plate to Create a Hollow ACS Bead



Materials:
20 gm Art Clay Silver 650
5 gm Art Clay Silver syringe
Green nozzle
Pencil
Speedy Stamp, Linoleum block, or carving pad
Carving Tools
Standard sized straw
Non-stick work surface
Regular light bulb or ornament x 2
Roller
Slats, 1.5mm and 1mm (6 cards & 4 cards)
Small ruler
Dehydrator or hair dryer
Olive oil
Flat end paintbrush
Files
600 and 1200 grit sandpaper
2” round cookie cutter
Liver of Sulfur
Hot water
Cold water
Scrap wire for hanging
Bamboo skewer
2 small bathroom cups
1 tbsp. baking soda
Programmable kiln or Butane Torch & Fire Brick
Fire blanket
Agate burnisher

 

Instructions:

  1. Draw a variety of small designs on the stamp surface with the pencil. Attach the “v” groove cutter tip into the handle. Carefully cut the designs out of the stamp, keeping the depth as even as possible.  Discard the stamp scrap.
  2. Apply a small amount of olive oil onto the round end of the bulb. Roll half of the clay into a ball. Flatten on the work surface, place your 1.5mm slats on either side of the Teflex, and roll into a circle about 2” in diameter.
  3. Transfer the circle onto your carved work surface, replace the 1.5mm slats with the 1mm slats, and roll into the texture you created, keeping the circle as round as possible.
  4. Flip the stamp over and allow the clay to fall off into your hand. Place the clay circle back onto the work surface. Use the 2” cookie cutter to cut out a perfect circle. Place a wet paper towel over the cut circle. Repeat Step 2-4.
  5. Lay the circles on top of each other gently. With the straw, cut half a circle out of the edge of the 2 clay circles. Go to the other side of the circle and do the same. When the sides are put together, this will be the opening for the chain or cord.
  6. Place the ornaments or light bulbs on top of the 2 bathroom cups. Oil the bulbs or ornaments lightly.
  7. Gently separate the clay circles and transfer them to the surface of the oiled light bulb or ornament near the end where it is roundest. Ease the edges of the circle down so they are flat against the bulb or ornament. Put a stop (a tool or paper) to prevent the bulb or ornament from rolling. Dry thoroughly.
  8. After the clay has dried, gently remove it from the bulb and continue to dry for several more minutes until no more moisture remains.
  9. To prepare to attach the two sides together, take a flat file and flatten the inside edge all the way around the bead half. Brush all of the filings onto the table but do not discard. Repeat with the other half.
  10. Before attaching the two halves, put them together dry, lining up the holes so they are opposite each other. Check the seams to make sure they meet properly all the way around.
  1. Separate the 2 halves again and, with the green nozzle on the Art Clay Syringe type, lay down a thick bead of syringe clay on the flat edge of the bead. While still wet, add the other side, making sure the holes line up. Apply a small amount of pressure to make sure the seams meet firmly. Smooth any syringe that squeezes through the seam with a damp paintbrush. Fill any seam cracks with additional syringe clay. Allow to dry.
  2. Use files, the 600 and 1200 grit sandpaper to smooth the seams without disturbing the texture. Repair any exposed seams as needed. Dry thoroughly
  3. Fire the bead on the fiber blanket at 1600 degrees F. for 10 minutes or with a butane torch for 3-4 minutes. Allow to cool.
  4. Brush the bead using the stainless steel brush. Burnish the design’s highlights with the agate burnisher until shiny. Alternatively, tumble the bead with 2lbs stainless steel shot, water and dish liquid or burnishing liquid for at least 1 ½ hours. Rinse thoroughly.
  5. Mix a thumbnail sized chunk of liver of sulfur (or a tablespoon of LOS Gel) into a cup of steaming hot water. Stir well with the bamboo skewer. Fill the second cup with clean, cold water. Fashion the length of scrap wire into a hook and hang the bead through the holes.
  6. Dip the bead very quickly into the hot water and then into the cold rinse water. Check the colors. You will first get gold, then amber, then magenta, then blue, then black, depending on how long you dip and how quickly you rinse. Continue to use the Liver of Sulfur until you get the colors you want. You can also take the entire bead to black, then use a polishing cloth to remove the patina from the high spots. Make a paste of the baking soda and water and gently rub the piece. Then rinse thoroughly under cold water and pat dry. Dispose of the liver of sulfur down the drain while running hot water for 1 minute.
  7. Complete your piece with the chain or cord of your choice. Your one-of-a-kind bead is now complete!

For more information visit www.artclayworld.com .

Katie Hacker & Jackie Truty

Copyright © 2012 Beads Baubles & Jewels. All Rights Reserved.